Author Message
 Post subject: Looking for DIN 41612 connectors
PostPosted: 30 Jan 2012, 16:08 
Offline

Joined: 29 Jan 2012, 10:59
Posts: 4
Hi all

I'm looking for DIN 41612 connector (16/32/64).

If someone know where I can find this part in a DIPTRACE library.


Thanks by advance.

Anode


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 09 Jun 2012, 14:23 
Offline

Joined: 09 Jun 2012, 14:07
Posts: 1
I suppose you have not received an answer to your Q.
As I am new here I will take a bit of time to learn the program and than will design the connectors and the IEC-3/3 board. If you have allready done so please share and spare me the time. Cheers, E


Top
 Profile  
 
 Post subject: how to become a model
PostPosted: 27 Jun 2012, 05:37 
Offline

Joined: 27 Jun 2012, 05:34
Posts: 1
DIN 41612 is a DIN standard for electrical connectors that are widely used in rack based electrical systems. Standardisation of the connectors is a pre-requisite for open systems, where users expect components from different suppliers to operate together. The mostly widely known use of DIN 41612 connectors is in the VMEbus system. They were also used by NuBus. The standard has subsequently been upgraded to international standards IEC 60603-2 and EN 60603-2.

FCI DIN 41612 Connectors are available at Mouser Electronics. Mouser offers inventory, pricing, datasheets & more on FCI DIN 41612 Connectors.

www.sapphiresmodel.com

_________________
how to become a model


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 31 Jul 2014, 22:00 
Offline

Joined: 31 Jul 2014, 21:51
Posts: 3
Reviving this thread a bit...

It's easy to find the DIN 41612 connectors (Molex, AMP, AVX, FCI and 3M all have C96ABC right-angle connectors which are available at Mouser or Digikey), but I can't seem to determine if the DipTrace components/patterns have these connectors. I've tried searching for the part numbers, and I also looked in the Pattern Editor, but I'm not coming up with anything.

Does a library exist for these connectors? Googling isn't much help either.

Thanks!

Rich


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 28 Aug 2014, 12:55 
Offline

Joined: 28 Aug 2014, 12:01
Posts: 2
I have a few PCB footprints & components for 32,24,64 & 96 way DIN41612 connectors. Don't know what the best way to share them is though?


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 29 Aug 2014, 08:29 
Offline

Joined: 31 Jul 2014, 21:51
Posts: 3
Great! I'm not sure but I think you can copy them to their own component and footprint libraries, ZIP the new libraries and then post them to the forum as a message attachment.


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 01 Sep 2014, 04:45 
Offline

Joined: 28 Aug 2014, 12:01
Posts: 2
Now I'm back at work I can attach the libs. Give them a go and tell me what you think.
Even though I created components and footprints for 32, 48, 64 & 96 way, I've only used the 48 & 64 way footprints on a board. The pads are a 39mil (1mm) hole with 64mil (1.5mm) overall diameter. The footprints are placed such that the component origin should align with the bottom right-hand corner of the board.

Edit: Uploaded photos
Edit2: Uploaded sensible size photos!


You do not have the required permissions to view the files attached to this post.


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 01 Sep 2014, 08:20 
Offline

Joined: 31 Jul 2014, 21:51
Posts: 3
jd_edmond wrote:
Now I'm back at work I can attach the libs. Give them a go and tell me what you think.
Even though I created components and footprints for 32, 48, 64 & 96 way, I've only used the 48 & 64 way footprints on a board. The pads are a 39mil (1mm) hole with 64mil (1.5mm) overall diameter. The footprints are placed such that the component origin should align with the bottom right-hand corner of the board.

Edit: Uploaded photos
Edit2: Uploaded sensible size photos!


Thanks very much! I will give them a look and let you know if there are any problems.


Top
 Profile  
 
 Post subject: Re: Looking for DIN 41612 connectors
PostPosted: 09 Feb 2016, 08:01 
Offline

Joined: 09 Feb 2016, 05:58
Posts: 1
Hi jd_edmond, would it be possible to get a copy of your board just to be sure that the connector ends upp at the right place? I only need the board outline and the connector of course, not your entire design ;) Thanx!


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 9 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group